Wednesday, 17 July 2013

Envelope needle case tutorial

The other day on Pinterest I was looking for a small sewing project to do with the girls from DCI (Dream Create Inspire craft group I teach at) and I came across this super cute needle case in the style of an envelope. I searched high and low for the tutorial but I couldn't find one so I thought I would have a go myself. This is my first tutorial so please bare with me! The photography isn't amazing and artistic, It's just done on my Iphone so apologies for that! If you find anything confusing or unclear, please write a comment at the bottom of this post and ill try and rectify it for you! Any feedback is appreciated!

Equipment and materials:
  • Medium weight Interfacing
  • Felt
  • Plain fabric
  • Patterned fabric
  • Pinking Shears
  • 1 Press stud/ Popper 

Firstly you need to download the pattern for the envelope from here, the template in the pictures doesn't have the seam allowance added on but the download will. You need to cut out one patterned piece for the inside and one plain colour for the outside.

You also need to cut one out of a medium weight interfacing. I like to use the iron on sort as it doesn't slip about! this will be used to stiffen the case and give it better structure. 

So you should have 3 bits all cut out now the same, one plain, for the outside, one patterned for the inside, and one piece of interfacing. Next Iron on the interfacing to the plain piece as this is reinforce the fabric for stitching the address. If you don't have iron on stuff, just leave it till later or pin it to the plain piece.

Next thing to do is to sew the lines of "address" on the front of the envelope, which is the plain fabric. I worked this out by folding up the envelope and working out roughly where it would go. Make sure you have the template up the correct way!! I just used straight stitch but if you had the time and inclination you could hand sew an actual address or someones name on it if you liked!

Now for the stamp, I cut out a piece of felt, using pinking shears to get the zig-zag effect and positioned it using the folded template again. Remember you have 1cm seam allowance around the edge, so don't go up to far into the corner. Stitch that down with straight stitch then you could sew  a button on, or embroider a little motif, I used a small piece of fabric (with a little dog on) and bondawebbed it on then stitched around it again (see end photos)

Now to cut out the felt pages for the inside of the booklet, again I just folded the flaps of the template in and then cut out a rectangle about 1.5cm smaller than the folded template.

Fold the felt to find out where the middle is and then using straight stitch just sew it straight down the middle.

Now to sew it altogether! so....you need to put the right sides together, so the side with the pages needs to be touching the side with the sewn on address and stamp. Interfacing, if you haven't ironed it on just needs to go on top of either side, it doesn't matter.

Stitch all the way around the outside of the needle case, keeping your 1cm away from the edge. DON'T SEW IT ALL UP! Remember to leave a gap on one of the long sides so you can turn it inside out. Before you turn it you need to remove the bulk from the corners to make it flatter when you turn it out. Cut diagonally across outward points, and cut triangles into the inward points. See the picture above.

When you have turned it inside out, use something pointy to point all the corners out, and then iron it. The open gap you have left can now be turned in, and then when you top stitch all the way round on the very edge, this should be sewn in too. If it isn't just use a needle and thread to slip stitch it shut.

All that's left to do now is to stitch in your poppers (or press studs, whatever you call them!), It doesn't really matter which way you do them, but they need to go onto the top and bottom flaps, not the side. i like to to the pointy one on the top so it can press down into the one with a hole in it. I should of used white thread here, but I was rushing to the end, I'm sure you will do a much better job!

So here is the finished one! You can see the little doggy I Bondawebed  and then stitched on. A little squiffy, but not too bad.

Here it is closed, for some reason my machine did a funny lump of thread where I started and stopped, and the point at the top of the envelope wouldn't fold in and so it looks a little shabby I'm ashamed to say (not like the amazing polished tutorials you get on other sites!!)
And here it is Half open so you can see how to fold it up!
 I hope that is pretty clear-if not-write a comment and Ill answer ASAP. O and I'd love to see your results if you have a go! ENJOY!

Pin It!